Shop
-
Relay and IO Modules
Four Stage Relay Module – IOR4
£38.60 Exc. VAT Exc. VAT Add to cartThe IOR4 is intended for use with BMS controllers to convert an analogue control output to a binary, staged, or sequenced relay modes. LEDs indicate correct operation and Hand/Off/Auto jumpers ease commissioning.
-
Relay and IO Modules
Max, Min, Average Module – IO6N1
£260.00 Exc. VAT Exc. VAT Add to cartThe IO6N1 is a microprocessor-controlled interface designed to provide maximum flexibility with a minimum cost.
-
Relay and IO Modules
Phase Cut Module 120VA – IOPC1-120
£125.00 Exc. VAT Exc. VAT Add to cartThe IOPC1-120 is designed to convert a single 0-10Vdc Input Signal to drive a 0-20V 50Hz phase-cut output, at 120VA, to drive larger valve and damper actuators.
-
Relay and IO Modules
Raise/Lower to Analogue Module – AUD
£175.00 Exc. VAT Exc. VAT Add to cartThe AUD converts a floating-point signal into a linear analogue output. There are Two inputs on the AUD, one to increase the analogue output and one to decrease the analogue output.
-
Relay and IO Modules
Single Channel Override Relay Module – IOMR1
£13.50 Exc. VAT Exc. VAT Add to cartThe IOMR1 is designed to provide a manual override of the output from a BMS Controller (or similar) and is particularly useful for commissioning or temporary control applications.
-
Relay and IO Modules
Six Stage Relay Module – IOR6
£49.00 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically it is used in such controls as valve and contacts changeover.
-
Relay and IO Modules
Three Stage Relay Module – IOR3
£34.60 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically it is used in such controls as valve and contacts changeover.
-
Relay and IO Modules
Two Stage Relay Module – IOR2
£29.00 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output signal to a time proportional raise/lower, high/low or binary relay output.
-
Relay and IO Modules
Volt Free To Voltage Converter – IOFS24-10
£35.00 Exc. VAT Exc. VAT Add to cartThe IOFS24-10 has been designed to give 3 dc voltages using volt-free inputs. The inputs can be adjusted between 0-10 volts.
-
Relay and IO Modules
Voltage to Current Conversion Module – IO-VI
£43.00 Exc. VAT Exc. VAT Add to cartThe IO-VI module will convert a 0-10 Volt Signal to 4-20mA current output. Din rail mounting with rising clamp terminals 24Vac/dc supply.
-
Fidelix IO Modules
Compact IO Module AI-8-C
£177.65 Exc. VAT Exc. VAT Add to cartThe 8 channel analogue input module is used to read input signals from active and passive sensors.
-
Fidelix IO Modules
Terminal-C Connector for Compact IO Modules
£8.36 Exc. VAT Exc. VAT Add to cartFdx-Terminal-C set: – 1 pcs female connector. – 1 pcs male connector. – 1 pcs 120 resistor. T-Bus DIN-rail connector.
-
Fidelix IO Modules
Compact IO Module AO-8-C
£229.90 Exc. VAT Exc. VAT Add to cartThe 8 channel analogue output module is used to generate voltage control signals.
-
Fidelix IO Modules
Compact IO Module DI-16-C
£135.85 Exc. VAT Exc. VAT Add to cartThe 16-channel digital input module is used to read and detect digital signals for indication, alarm, or impulse measurement purposes.
-
Fidelix IO Modules
Compact IO Module DO-8-C
£130.63 Exc. VAT Exc. VAT Add to cartThe 8-channel digital output module has 8 changeover relays, capable of taking on a maximum load of 2A at 24 VAC, or 6A at 12 VDC.
-
Fidelix IO Modules
Compact IO Module DOOC-16-C
£188.10 Exc. VAT Exc. VAT Add to cartThe 16-channel digital output module has 16 open collector outputs, each capable of taking on a maximum load of 100 mA.
