ECP
EC Products was established in 2006, distributing imported products from around the world to the UK HVAC market.
In 2008, the decision was made to invest in developing and manufacturing our own product range, to be produced at our premises in Hounslow.
This introduction enabled ECP to respond to customer demand for next-day delivery, supplying British-manufactured, high-quality products.
They are now the one-stop shop for both BMS peripherals and everything panel builders require, from panel lamps to Steel enclosures.
-
Relay and IO Modules
Eight Stage Relay Module – IOR8
£70.00 Read moreThe IO-RM8 is intended for use with BMS controllers to convert an analogue control output to staged or sequenced relay modes.
LEDs indicate correct operation, and Hand/Off/Auto jumpers ease commissioning. -
Relay and IO Modules
Electro-pneumatic Converter – IOEPC
£250.00 Add to basketThe IOEPC is an electric-to-pneumatic transducer which converts an analogue input signal to a proportional pneumatic output. The unit will automatically modulate its control valve to regulate the branch-line pressure to the selected set point, as determined by the input signal.
-
Relay and IO Modules
Four Channel Override Relay Module – IORM04
£95.00 Add to basketFour Channel Override Relay Module – IO RM04
-
Relay and IO Modules
Four Stage Relay Module – IOR4
£47.25 Add to basketThe IOR4 is intended for use with BMS controllers to convert an analogue control output to a binary, staged, or sequenced relay mode. LEDs indicate correct operation, and Hand/Off/Auto jumpers ease commissioning.
-
Relay and IO Modules
Max, Min, Average Module – IO6N1
£260.00 Add to basketMax, Min, Average Module – IO6N1
-
Relay and IO Modules
Phase Cut Module 120VA – IOPC1-120
£175.00 Add to basketThe IOPC1-120 is designed to convert a single 0-10Vdc input signal into a 0-20V 50Hz phase-cut output at 120VA to drive larger valve and damper actuators. The IOPC1-120 features an optoisolator powered by 24Vac (with a common connection to the input signal) and high-quality rising-clamp screw terminals.
-
Relay and IO Modules
Raise/Lower to Analogue Module – AUD
£193.00 Add to basketRaise/Lower to Analogue Module – AUD
-
Relay and IO Modules
Single Channel Override Relay Module – IOMR1
£15.75 Add to basketSingle Channel Override Relay Module – IOMR1
-
Relay and IO Modules
Six Stage Relay Module – IOR6
£55.65 Add to basketSix Stage Relay Module – IOR6
-
Relay and IO Modules
Three Stage Relay Module – IOR3
£34.60 Add to basketThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically, it is used in controls such as valves and contact changeovers.
-
Relay 24Vac Coil
Two Stage Relay Module – IOR2
Original price was: £39.50.£35.00Current price is: £35.00. Add to basketThis IO module is used with DDCs to convert an analogue control output signal to a time-proportional raise/lower, high/low or binary relay output.
Typically, it is used to control valve and damper actuators from an analogue signal. -
FCU Controllers
Volt Free To Voltage Converter – IOFS24-10
£35.00 Add to basketThe IOFS24-10 has been designed to provide 3 DC voltages from voltage-free inputs. The inputs can be adjusted to 0-10 volts. This module can be used for switched fan speed control where a 0-10 volt signal is needed, but only 3 speeds are needed.
-
Air
Voltage to Current Conversion Module – IO-VI
£43.00 Add to basketThe IO-VI is designed to convert a 0-10Vdc input signal to a 4-20mA current output. The IO-VI is supplied in a DIN Rail carrier suitable for mounting on a TS35 DIN Rail section and features high-quality rising clamp terminals for ease of connection. The unit is powered by 24 Vac/dc and can power a current-loop signal.
-
Liquid
Liquid Static Pressure Sensor 4-20mA
£136.00 Select options This product has multiple variants. The options may be chosen on the product pagePlease select the Pressure range below
-
Liquid
Liquid Differential Pressure Switch LDP
£116.00 Select options This product has multiple variants. The options may be chosen on the product pagePlease select the Pressure range required from below
-
Liquid
Connection kit for use with the FD113
£32.00 Add to basketBrass Fitting 1/4″ bspt to 6mm Compression and 6mm copper tube.
