Adjustable
-
Relay and IO Modules
Adjustable Single Relay Module – IOVR1
£27.35 Exc. VAT Exc. VAT Add to cartThe IOVRI is an SPCO change over relay output from 0 to 10Vdc with a fully adjustable switch point.
-
Relay and IO Modules
Analogue Rescaling Module – ARM
£89.25 Exc. VAT Exc. VAT Add to cartThe IOVRI is an SPCO change over relay output from 0 to 10Vdc with a fully adjustable switch point.
-
Relay and IO Modules
Analogue to 20 Relay Card – IOAD20
£128.00 Exc. VAT Exc. VAT Add to cartThe IOAD20 has been designed primarily for fault indication of up to 20 alarms from 1 analogue signal.
-
Relay and IO Modules
Current Monitoring Relay – CMR5-VFC
£23.50 Exc. VAT Exc. VAT Add to cartThe Current Monitoring Relay is designed to monitor Current to equipment and can be set to switch the volt free contact at a set current, also there is an adjustable time delay to eliminate current peaks.
-
Relay and IO Modules
Dual Phase Cut Module 30VA per channel – IOPC2
£76.00 Exc. VAT Exc. VAT Add to cartThe IOPC2 converts two 0-10V dc Input Signals to drive two separate 0-20V 50Hz phase-cut outputs, at 30VA per channel for the control of small valve or damper actuators.
-
Relay and IO Modules
Eight Stage Relay Module – IOR8
£70.00 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output to a staged, reverse staged, or sequenced relay output.
-
Relay and IO Modules
Electro-pneumatic Converter – IOEPC
£152.00 Exc. VAT Exc. VAT Add to cartThe IOEPC is an electric to pneumatic transducer which converts an analogue input signal to a proportional pneumatic output.
-
Relay and IO Modules
Four Channel Override Relay Module – IO RM04
£82.00 Exc. VAT Exc. VAT Add to cartThe IOMR4 is designed for applications that require an independent manual override of digital output channels from BMS Controllers.
-
Relay and IO Modules
Four Stage Relay Module – IOR4
£38.60 Exc. VAT Exc. VAT Add to cartThe IOR4 is intended for use with BMS controllers to convert an analogue control output to a binary, staged, or sequenced relay modes. LEDs indicate correct operation and Hand/Off/Auto jumpers ease commissioning.
-
Relay and IO Modules
Max, Min, Average Module – IO6N1
£260.00 Exc. VAT Exc. VAT Add to cartThe IO6N1 is a microprocessor-controlled interface designed to provide maximum flexibility with a minimum cost.
-
Relay and IO Modules
Phase Cut Module 120VA – IOPC1-120
£125.00 Exc. VAT Exc. VAT Add to cartThe IOPC1-120 is designed to convert a single 0-10Vdc Input Signal to drive a 0-20V 50Hz phase-cut output, at 120VA, to drive larger valve and damper actuators.
-
Relay and IO Modules
Raise/Lower to Analogue Module – AUD
£175.00 Exc. VAT Exc. VAT Add to cartThe AUD converts a floating-point signal into a linear analogue output. There are Two inputs on the AUD, one to increase the analogue output and one to decrease the analogue output.
-
Relay and IO Modules
Single Channel Override Relay Module – IOMR1
£13.50 Exc. VAT Exc. VAT Add to cartThe IOMR1 is designed to provide a manual override of the output from a BMS Controller (or similar) and is particularly useful for commissioning or temporary control applications.
-
Relay and IO Modules
Six Stage Relay Module – IOR6
£49.00 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically it is used in such controls as valve and contacts changeover.
-
Relay and IO Modules
Three Stage Relay Module – IOR3
£34.60 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically it is used in such controls as valve and contacts changeover.
-
Relay and IO Modules
Two Stage Relay Module – IOR2
£29.00 Exc. VAT Exc. VAT Add to cartThis IO module is used with DDCs to convert an analogue control output signal to a time proportional raise/lower, high/low or binary relay output.
