Shop
Showing 897–912 of 1170 resultsSorted by popularity
-
Relay and IO Modules
Four Stage Relay Module – IOR4
£47.25 Add to basketThe IOR4 is intended for use with BMS controllers to convert an analogue control output to a binary, staged, or sequenced relay mode. LEDs indicate correct operation, and Hand/Off/Auto jumpers ease commissioning.
-
Relay and IO Modules
Max, Min, Average Module – IO6N1
£260.00 Add to basketMax, Min, Average Module – IO6N1
-
Relay and IO Modules
Phase Cut Module 120VA – IOPC1-120
£175.00 Add to basketThe IOPC1-120 is designed to convert a single 0-10Vdc input signal into a 0-20V 50Hz phase-cut output at 120VA to drive larger valve and damper actuators. The IOPC1-120 features an optoisolator powered by 24Vac (with a common connection to the input signal) and high-quality rising-clamp screw terminals.
-
Relay and IO Modules
Raise/Lower to Analogue Module – AUD
£193.00 Add to basketRaise/Lower to Analogue Module – AUD
-
Relay and IO Modules
Single Channel Override Relay Module – IOMR1
£15.75 Add to basketSingle Channel Override Relay Module – IOMR1
-
Relay and IO Modules
Six Stage Relay Module – IOR6
£55.65 Add to basketSix Stage Relay Module – IOR6
-
Relay and IO Modules
Three Stage Relay Module – IOR3
£34.60 Add to basketThis IO module is used with DDCs to convert an analogue control output to a binary, heat/cool, staged, or sequenced relay output. Typically, it is used in controls such as valves and contact changeovers.
-
Relay 24Vac Coil
Two Stage Relay Module – IOR2
£39.50Original price was: £39.50.£35.00Current price is: £35.00. Add to basketThis IO module is used with DDCs to convert an analogue control output signal to a time-proportional raise/lower, high/low or binary relay output.
Typically, it is used to control valve and damper actuators from an analogue signal. -
FCU Controllers
Volt Free To Voltage Converter – IOFS24-10
£35.00 Add to basketThe IOFS24-10 has been designed to provide 3 DC voltages from voltage-free inputs. The inputs can be adjusted to 0-10 volts. This module can be used for switched fan speed control where a 0-10 volt signal is needed, but only 3 speeds are needed.
-
Air
Voltage to Current Conversion Module – IO-VI
£43.00 Add to basketThe IO-VI is designed to convert a 0-10Vdc input signal to a 4-20mA current output. The IO-VI is supplied in a DIN Rail carrier suitable for mounting on a TS35 DIN Rail section and features high-quality rising clamp terminals for ease of connection. The unit is powered by 24 Vac/dc and can power a current-loop signal.
-
Fidelix IO Modules
Compact IO Module AI-8-C
£177.65 Add to basketThe 8-channel analogue input module is used to read input signals from active and passive sensors. Its 8 individually configurable channels can read data from resistive sensors, current loops, voltage messages, and digital indications.
-
Fidelix IO Modules
Terminal-C Connector for Compact IO Modules
£8.36 Add to basketTerminal-C set: – 1 pcs female connector. – 1 pcs male connector. – 1 pcs 120 Ω resistor. T-Bus DIN-rail connector.
-
Fidelix IO Modules
Compact IO Module AO-8-C
£229.90 Add to basketThe 8 channel analogue output module is used to generate voltage control signals.
-
Fidelix IO Modules
Compact IO Module DI-16-C
£135.85 Add to basketThe 16-channel digital input module is used to read and detect digital signals for indication, alarm, or impulse measurement purposes.
-
Fidelix IO Modules
Compact IO Module DO-8-C
£130.63 Add to basketThe 8-channel digital output module has 8 changeover relays, capable of taking on a maximum load of 2A at 24 VAC, or 6A at 12 VDC.
-
Fidelix IO Modules
Compact IO Module DOOC-16-C
£188.10 Add to basketThe 16-channel digital output module has 16 open collector outputs, each capable of taking on a maximum load of 100 mA.






























