0-10V
-
Gas Sensors
Static Positive Pressure Transmitter 0-10VDC – Bailey & Mackey
£185.00 Select options This product has multiple variants. The options may be chosen on the product pagePlease select the pressure range from the below options
-
Relay and IO Modules
Adjustable Single Relay Module – IOVR1
£27.35 Add to basketThe IOVRI is an SPCO change-over relay output from 0 to 10Vdc with a fully adjustable switch point. The unit also has a buffered 0-10Vdc output, which will allow one 0-10V input to be passed on to another device.
-
Relay and IO Modules
Analogue Rescaling Module – ARM
£125.00 Add to basketThe ARM analogue re-scaling module accepts voltage or current inputs and rescales them to voltage or current outputs. A range of preset values is link-selectable, and fine adjustments can be made using trim potentiometers.
-
Relay and IO Modules
Analogue to 20 Relay Card – IOAD20
£135.00 Add to basketThe IOAD20 has been designed primarily for fault indication of up to 20 alarms from 1 analogue signal. It provides 20-volt free-changeover contacts and 1 common-output contact.
-
Relay and IO Modules
Current Monitoring Relay – CMR5-VFC
£23.50 Add to basketThe Current Monitoring Relay is designed to monitor Current to equipment and can be set to switch the voltage-free contact at a set current. There is an adjustable time delay to eliminate current peaks. It can also be used with a current transformer to monitor higher currents. It has an LED indicator and is Din-rail mounting.
-
Relay and IO Modules
Dual Phase Cut Module 30VA per channel – IOPC2
£92.00 Add to basketThe IOPC2 converts two 0-10V DC input signals to drive two separate 0-20V 50Hz phase-cut outputs, at 30VA per channel, for the control of small valve or damper actuators. The IOPC2 features an optoisolator that is powered from 24V ac (with a common connection to the input signal) and has Rising Clamp Screw Terminals. The output from the IOPC2 can be boosted to 60VA by using two IOPCA1, 1 per channel.
-
Relay and IO Modules
Eight Stage Relay Module – IOR8
£70.00 Read moreThe IO-RM8 is intended for use with BMS controllers to convert an analogue control output to staged or sequenced relay modes.
LEDs indicate correct operation, and Hand/Off/Auto jumpers ease commissioning. -
Relay and IO Modules
Electro-pneumatic Converter – IOEPC
£250.00 Add to basketThe IOEPC is an electric-to-pneumatic transducer which converts an analogue input signal to a proportional pneumatic output. The unit will automatically modulate its control valve to regulate the branch-line pressure to the selected set point, as determined by the input signal.
-
Relay and IO Modules
Four Channel Override Relay Module – IORM04
£95.00 Add to basketFour Channel Override Relay Module – IO RM04
-
Relay and IO Modules
Four Stage Relay Module – IOR4
£47.25 Add to basketThe IOR4 is intended for use with BMS controllers to convert an analogue control output to a binary, staged, or sequenced relay mode. LEDs indicate correct operation, and Hand/Off/Auto jumpers ease commissioning.
-
Relay and IO Modules
Max, Min, Average Module – IO6N1
£260.00 Add to basketMax, Min, Average Module – IO6N1
-
Relay and IO Modules
Phase Cut Module 120VA – IOPC1-120
£175.00 Add to basketThe IOPC1-120 is designed to convert a single 0-10Vdc input signal into a 0-20V 50Hz phase-cut output at 120VA to drive larger valve and damper actuators. The IOPC1-120 features an optoisolator powered by 24Vac (with a common connection to the input signal) and high-quality rising-clamp screw terminals.
-
Relay and IO Modules
Raise/Lower to Analogue Module – AUD
£193.00 Add to basketRaise/Lower to Analogue Module – AUD
-
Relay and IO Modules
Single Channel Override Relay Module – IOMR1
£15.75 Add to basketSingle Channel Override Relay Module – IOMR1
